How to Remove Water Spots from Your Car
Water spots can be a hassle and keep your car from looking its best. That's why we've created a great solution.
Water spots form when droplets land on your car’s paint and other surfaces. As the water evaporates, minerals left behind create a stain.
If you catch these spots early, they can be wiped away easily during a wash or with a quick detail spray. If left overnight, they may become more stubborn, but a clay bar can usually remove them. However, if the spots are allowed to sit longer, they can penetrate the surface, leading to permanent damage that might require polishing, wet sanding, or even repainting.
Our Graphene Pro 10H & N1‘s advanced Nanotechnology, combined with the properties of graphene, makes this coating the perfect, superior product in the car care industry, which is like no other.
Graphene Pro provides the ultimate shield for painted surfaces, metal surfaces, metal, and glass against damage with its 100% guaranteed chemical, scratch, and pollutant resistance that lasts a lifetime. This Ceramic Coating provides a thick layer of protection up to 1000nm. Graphene Pro can achieve a super smooth, extremely glossy, and hydrophobic invisible layer of protection through a simple application process.
Why ONYX COATING’s Graphene Pro 10H & N1.
- World’s First N1 Nano Coating – ONYX COATING is the pipneer of manufacturing a combined 10H & N1 coating product in the market. At the ONYX COATING Innovation Lab, our team continuously innovates, tests quality, and brings out products at such a high level of quality. And before they’re ready to be packed and shipped, each product is certified—we back our claims with actual proof!
- 10H Hardness – Each product has been developed, tested, and certified to offer the highest grade of hardness and protection, making ours the world’s #1 N1 coating product line.
- Stays Lifetime – It’s proven that once applied, the coating can last ling for a lifetime.
- Contains up to 0.5% Graphene (up to 300 layers)
How to apply ONYX COATING Graphene Pro 10H & N1
Paint Preparation
- Restore paint before application. ONYX COATING is not a paint restorer; any claying, polishing, and restoration work should be carried out before application.
Best results are achieved with Body Shop Safe compounds containing no wax or fillers that will have to be removed before the application.
- Wash and dry paintwork.
- Remove wax and sealants from the paint surface. Use ONYX COATING Paint Prep using similar solvent-based paint prep product by applying enough to dampen a cloth and rub over the paintwork.
- Test an inconspicuous area to confirm compatibility, pay special attention to airbrushed or custom paintwork. Depending on wax/sealant/tar deposits additional towel(s) may be needed. Do not leave Paint Prep dampened rags on paintwork
Application
You may apply the product on a small section of a side window to gauge how quickly the product will dry at a given temperature. This way, you can apply the product to smaller sections to compensate for faster drying.
- Wipe on Onyx Surface Protection coating, covering an entire panel or panel section evenly with a thin coat. Any “touch-ups” of missed spots should be done after the initial product has been buffed (step 2). If additional coats are desired, wait until the initial coating is fully hardened (1-4 Hours).
- Approximately 1-5 minutes after application (depending on temperature and humidity) to the panel or section gently buff to a gloss with a dry microfiber towel. Do not allow the product to dry completely.
- In high (100° F +, 38° C +) temperatures drying time may need to be reduced to less than 1 minute ensure that coating not dried completely.
- If you notice any missed spots after buffing, you can re-treat the spot with ONYX COATING Resin and re-buff the area with a microfiber towel.
- Always test an inconspicuous area to confirm compatibility, pay special attention to airbrushed or custom paintwork.
- Be sure to check all areas after application to make sure no spots need re-buffing.
- Ready for light / dry driving after 8 hrs. Product cures within 4 hours. Coating will exhibit additional hardening over the next 7-14 days
